Machining Tech II - 2nd Shift Assembly
Company: Howmet Aerospace
Location: Fullerton
Posted on: June 25, 2022
|
|
Job Description:
Qualifications Able to read/interpret part drawings, use quality
tools (calipers, mics, comparators) are preferred. Employees must
be legally authorized to work in the United States. Verification of
employment eligibility will be required at the time of hire. Visa
sponsorship is not available for this position. This position is
subject to the International Traffic in Arms Regulations (ITAR)
which requires U.S. person status. ITAR defines U.S. person as an
U.S. Citizen, U.S. Permanent Resident (i.e. 'Green Card Holder'),
Political Asylee, or Refugee. Verification of employment
eligibility will be required at the time of hire. High school
diploma or General Education Degree (GED) preferred; or one to two
years related experience and/or training; or equivalent combination
of education and experience. Ability to add, subtract, multiply,
and divide in all units of measure, using whole numbers, common
fractions, and decimals. Ability to compute rate, ratio, and
percent and to draw and interpret bar graphs. Ability to apply
common sense understanding to carry out instructions furnished in
written, oral, or diagram form. Ability to deal with problems
involving several concrete variables in standardized situations.
Knowledge of Syteline Manufacturing software. Qualifications Able
to read/interpret part drawings, use quality tools (calipers, mics,
comparators) are preferred. Employees must be legally authorized to
work in the United States. Verification of employment eligibility
will be required at the time of hire. Visa sponsorship is not
available for this position. This position is subject to the
International Traffic in Arms Regulations (ITAR) which requires
U.S. person status. ITAR defines U.S. person as an U.S. Citizen,
U.S. Permanent Resident (i.e. 'Green Card Holder'), Political
Asylee, or Refugee. Verification of employment eligibility will be
required at the time of hire. High school diploma or General
Education Degree (GED) preferred; or one to two years related
experience and/or training; or equivalent combination of education
and experience. Ability to add, subtract, multiply, and divide in
all units of measure, using whole numbers, common fractions, and
decimals. Ability to compute rate, ratio, and percent and to draw
and interpret bar graphs. Ability to apply common sense
understanding to carry out instructions furnished in written, oral,
or diagram form. Ability to deal with problems involving several
concrete variables in standardized situations. Knowledge of
Syteline Manufacturing software. Operates and maintains, after
set-up by others, any or all standard or specialized production
machines in use by the company including but not limited to lathes,
mills and drillers. Operator will be held to established production
and quality standards. Incumbent will have control to make minor
adjustments to the process or machines after tasks are assigned.
After set-up by others, operates various standard and specialized
machines to precision tolerances and maintains set-ups completed by
others. Performs minor adjustments and tool changes. Operates one
or more machines according to crew size called out on work order.
Performs typical operations as: Loading parts/material into bins,
hoppers and feeders; removing finished parts; and operating
switches, pedals, and levers, uses standard gauges to check part
Observes operations for malfunction or improper processing;
corrects or reports them as needed. If the malfunction cannot be
corrected, stops the process and contacts supervisor. Performs
other related tasks in departments to which assigned such as:
Assembling, drilling, deburring, sorting, counting, etching,
stamping, recording of parts processed and housekeeping Required to
check multiple operations on a part, such as: O.D., I.D., overall
height, thread gauging, perpendicularity gauge, etc. Reads
micrometers, indicators, plug gauges, and thread gauges. Reads work
order routers and related blueprints, sets-up and maintains S.P.C.
charts. Must have an understanding of cutting tools, drills and
taps Performs required S.P.C. to establish machine capability for
all machines in the department. Responsible for submitting "first
article" to print. Assist factory supervision and leaders in the
training of machine operators. Parts to be lifted and/or
transported may weigh up to 30 lbs. Keeps work area clean, safe and
in an orderly fashion on a daily basis. Performs other tasks of
equal or lesser skill as required. Operates and maintains, after
set-up by others, any or all standard or specialized production
machines in use by the company including but not limited to lathes,
mills and drillers. Operator will be held to established production
and quality standards. Incumbent will have control to make minor
adjustments to the process or machines after tasks are assigned.
After set-up by others, operates various standard and specialized
machines to precision tolerances and maintains set-ups completed by
others. Performs minor adjustments and tool changes. Operates one
or more machines according to crew size called out on work order.
Performs typical operations as: Loading parts/material into bins,
hoppers and feeders; removing finished parts; and operating
switches, pedals, and levers, uses standard gauges to check part
Observes operations for malfunction or improper processing;
corrects or reports them as needed. If the malfunction cannot be
corrected, stops the process and contacts supervisor. Performs
other related tasks in departments to which assigned such as:
Assembling, drilling, deburring, sorting, counting, etching,
stamping, recording of parts processed and housekeeping Required to
check multiple operations on a part, such as: O.D., I.D., overall
height, thread gauging, perpendicularity gauge, etc. Reads
micrometers, indicators, plug gauges, and thread gauges. Reads work
order routers and related blueprints, sets-up and maintains S.P.C.
charts. Must have an understanding of cutting tools, drills and
taps Performs required S.P.C. to establish machine capability for
all machines in the department. Responsible for submitting "first
article" to print. Assist factory supervision and leaders in the
training of machine operators. Parts to be lifted and/or
transported may weigh up to 30 lbs. Keeps work area clean, safe and
in an orderly fashion on a daily basis. Performs other tasks of
equal or lesser skill as required.
Keywords: Howmet Aerospace, Fullerton , Machining Tech II - 2nd Shift Assembly, Other , Fullerton, California
Click
here to apply!
|